Start with the back

Quilt backing calculator

Find the fabric you need, compare both seam directions, and take a clear cutting plan to the shop.

Your next cut, considered.

Your measurements

View 5 yd cutting plan
Try a size
Choose a starting width, then measure your fabric.
Exclude both selvedges.
Ask your quilting service.
More options+
Per piece at each seam.
Choose by the actual print on your fabric. The other layout is excluded; upright motifs do not always follow the selvedge.
0 for none. One repeat per joined panel is a reserve only; crosswise matching is not calculated.

Updates as you type

Fabric to buy

5 yd

2 panels · vertical seams

Cut plan included

Rounded up to ⅛ yard. Before shop rounding: 4.889 yd.

68 in × 88 in assembled122 panels · 34.5 in × 88 in each
Dashed white line: quilt top. Panel colours show the joins.
Required backing
68 in × 88 in
Panels off the bolt
2 × 88 in long
Each panel across the bolt
34.5 in
Total seam take-up
1 in
Calculated cut length
176 in · 4.889 yd
Separate repeat reserve
0 in
Added by shop rounding
4 in

Compare layouts

  1. Cut 2 full-width lengths, each 88 in along the bolt. From each, cut a panel 34.5 in across the bolt × 88 in along it.
  2. Join the 2 panels with a 0.5 in seam allowance on each piece. Each join takes up 1 in across the assembled back. Press seams open.
  3. Before final trimming, the assembled back measures 68 in × 88 in. The backing target is 68 in × 88 in.
  4. Centre the quilt and check coverage, then trim the assembled back to 68 in × 88 in.
At the fabric counter
Backing fabric5 yd

Cut lengths total 176 in off the bolt. Shop rounding adds 4 in. That rounding is not a planned shrinkage or squaring allowance.

No automatic prewash shrinkage, squaring or crosswise motif matching. Measure usable width after any washing. Check your quilting service’s overhang and seam requirements.

A few useful things to know

How to use this backing calculator

A quilt back needs room beyond the quilt top. Enter your finished top size and the usable width of your fabric. We compare two balanced-panel layouts and keep every seam allowance in the calculation.

  1. Measure the whole quilt top, including any borders.
  2. Add the overhang your quilting service requires on every side. Four inches is a starting point, not a universal longarm requirement.
  3. Measure between the selvedges after removing them. A bolt sold as 44 inches may provide only 42 usable inches.
  4. Review the two seam directions, then copy the shopping list or download the cutting plan.

A worked example

For a 60 × 80 inch quilt, 4 inches of overhang, 42 inches of usable fabric and ½ inch seams, the backing must cover 68 × 88 inches. Cut two panels at least 34½ × 88 inches for vertical seams: 176 inches off the bolt, or 4.889 yards. Rounded up to an eighth, buy 5 yards. Horizontal seams need three 68-inch lengths: 204 inches, rounded to 5¾ yards.

The method behind the result

Required backing = quilt size + twice the overhang. For a joined width B, usable bolt width F and seam allowance s, the smallest panel count is ceil((B − 2s) / (F − 2s)). Every join consumes 2s. Yardage is the sum of panel cut lengths, plus any separate matching reserve.

What this plan assumes

Panels are balanced in width, all cut from one fabric, with ordinary straight seams pressed open. The least fabric result is selected among the two supported regular-panel layouts. Scraps, inset strips and diagonal piecing are outside this comparison. Fabric width means usable width after selvedges; shrinkage and squaring-up fabric are not automatically included.

Common mistakes to avoid

  • Entering the bolt label width instead of the usable fabric width.
  • Adding overhang only once rather than on both sides.
  • Buying for a two-panel join without subtracting the seam loss.
  • Choosing a cheaper layout that turns an upright print sideways.